Artículo en PDF
How to cite
Complete issue
More information about this article
Journal's homepage in redalyc.org
Sistema de Información Científica
Red de Revistas Científicas de América Latina y el Caribe, España y Portugal
OZONATION AND SOL-GEL METHOD TO OBTAIN Cu/CuO NANOPARTICLES FROM
CYANIDATION WASTEWATER
María de Jesús SORIA AGUILAR
1
, Damaris Margarita PUENTE SILLER
1
,
Francisco Raúl CARRILLO PEDROZA
1
*, Luis Alfonso GARCÍA CERDA
2
and
Jesús VELÁZQUEZ SALAZAR
3
1
Facultad de Metalurgia, Universidad Autónoma de Coahuila, Carretera 57 K. 4.5, Monclova, Coahuila, México,
C.P. 25710
2
Centro de Investigación en Química Aplicada, Blvd. Enrique Reyna No. 140 Col. Los Pinos, Saltillo, Coahuila,
México, C.P. 25253
3
Department of Physic and Astronomy, University of Texas at San Antonio, One UTSA Circle, San Antonio
TX 78249
* Autor de correspondencia: frrcarrillo@yahoo.com.mx
(Recibido noviembre 2014; aceptado enero 2015)
Key words: cyanide, gold mining efFuents, nanoparticles, copper
ABSTRACT
The extraction process of gold and silver by cyanidation generates large amounts of
efFuent which also contain contaminants such as cyanide and signi±cant metal values
such as copper. This paper presents the results of the removal and recovery of cop-
per from ozonation treatment of a residual aqueous cyanide. The residual solution
was treated by ozonation-precipitation to obtain a precipitate of copper. From this,
copper nanocomposites obtained by Pechini modi±ed sol-gel method were obtained.
The compounds obtained were characterized by XRD, showing a dependence of the
type of compounds formed over time of ozonation and heat treatment of the gel. The
particle size was measured by SEM and calculated by the Scherrer equation, being
between 50 and 120 nm.
Palabras clave: cianuro, eFuentes de la minería del oro, nanopartículas, cobre
RESUMEN
El proceso de extracción de oro y plata por cianuración genera grandes cantidades de
eFuentes que contienen, además de contaminantes como el cianuro, valores importantes
de metales, como el cobre. En este trabajo se presentan los resultados de la remoción y
recuperación de cobre a partir del tratamiento por ozonización de una solución acuosa
residual de cianuración. La solución residual fue tratada por ozonización-precipitación
para obtener un precipitado de cobre. A partir de este precipitado se obtuvieron nano-
compuestos de cobre por el método de sol-gel modi±cado de Pechini. Los compuestos
obtenidos fueron caracterizados por difracción de rayos X, en los que se observó una
dependencia del tipo de compuestos formados con el tiempo de ozonización y el trata-
miento térmico del gel. El tamaño de partícula fue medido por microscopía electrónica de
barrido y calculado por la ecuación de Scherrer, con un resultado de entre 50 y 120 nm.
Rev. Int. Contam. Ambie. 31 (3) 265-270, 2015
M.J. Soria Aguilar
et al.
266
INTRODUCTION
Cyanide has been widely used as an essential ma-
terial in several industries including textile, plastics,
paints, photography, electroplating, agriculture, food,
medicine and mining/metallurgy. Because of its high
afFnity for gold and silver, cyanide is able to selec
-
tively dissolve or leach these metals from ores. This
is called ‘‘cyanidation’’ process (Habashi 1966, Rubo
et al
. 2006). After gold and silver are extracted from
a cyanide solution, wastewater or process solutions
may contain three principle types of cyanide com-
pounds: free cyanide, weakly complexed cyanide and
strongly complexed cyanide. Cyanide forms ionic
complexes with metals (e.g. Fe, Cu, Zn). Stability
of cyanide-metal complexes may vary depending
on the type of metal. Weak acid dissociable Cu and
Zn complexes are relatively unstable (Ministry of
Environment Ontario 2013). Cyanide in ef±uents
resulting from gold mining is known to be the prime
candidate for treatment. However, according to many
studies, ammonia, suspended solids and copper are
identiFed as the most important contaminants in
gold mining ef±uents rather than cyanide (Mudliara
et al.
2009). Then, gold mining ef±uents can be an
important source of valuable metals.
Many methods have been investigated to cyanide
destruction and metal recovery. In this work, ozone
is used with this purpose. Ozone, as a strong oxidiz-
ing reagent has been used to destroy cyanide. Ozone
is generated on-site typically by the silent electrical
discharge method. One advantage is the ability of
ozone to destroy zinc, copper and nickel cyanide
complexes, obtaining metallic hydroxides or oxides
precipitates (Mudliara
et al
. 2009). In this context,
the present study is focused in obtaining copper
oxide nanoparticles from gold mining ef±uents by
a combination of two techniques: ozone oxidation-
precipitation and Pechini modiFed sol-gel method.
Particularly, nanoparticles have been the subject
of intense scientiFc and technological research due to
their interesting size-dependent physicochemical and
optoelectronic properties, and consequently exciting
application potential in many important Felds of sci
-
ence and technology as sensors, electrochemical cells,
optical devices and catalysts (Kakihana 1996, Ren
et
al
. 2009, Theivasanthi and Alagar 2011). Moreover,
one of the most important challenges is the compre-
hensive utilization of waste to obtain metal values us-
ing methods and techniques that demand less energy
consumption, environmentally friendly and economi-
cally favorable (Segal 1997). The oxides of transition
metals are an important class of semiconductors,
which have applications in magnetic storage media,
solar energy transformation, electronics and catalysis.
Among the oxides of transition metals, copper oxide
nanoparticles are of special interest as a less expen-
sive alternative (Lanje
et al
. 2010). The research
rapidly turned towards amorphous materials based
on dispersed CuO due to their better hydrothermal
and mechanical stability. Copper-based catalysts
have been reported to have a superior performance
in hydrogenolysis of glycerol (Huang
et al.
2009),
hydrogen production by methanol (Gadhe and Gupta
2007) and the reduction of nitrogen oxides (NOx)
with reducing species (hydrocarbon) in high oxidant
atmosphere (Bennici
et al
. 2003).
In our study, Pechini modiFed sol-gel method
was used to obtain the nanoparticles. In this method,
a solution of metal-organic compounds (such as
metal alkoxides) is used to form a gelled material,
a network of polymer chains formed by hydrolysis
and condensation reactions (Rahaman 2007). This
polymeric precursor method is one of the ways of
obtaining catalysts with a high degree of dispersion
and uniform component distribution (Gvishi 2009).
This method was initially intended for the synthesis
of oxide ceramics in electronic applications, but
later it found wide use in the syntheses of catalytic
materials, as copper oxides (Potemkina
et al.
2010).
MATERIALS AND METHODS
Industrial gold mining ef±uents samples (free
CN
, 700 mg/L; Cu, 626.7 mg/L; Zn, 5.58 mg/L; Fe,
3.16 mg/L; pH, 11; 20 ºC) were placed in a type-col-
umn ozonation reactor and then oxidized with ozone
(produced by L-22 PaciFc Ozone generator) in order
to remove cyanide. Experiments were performed at
constant ozone ±ow rate of 1 g O
3
/h during different
ozonation times. After ozone
oxidation and subse-
quent solid-liquid separation, metallic nanoparticles
were synthesized using the sol-gel method. Citric
acid (CA) and ethylene glycol (EG) obtained from
the ozonized solution were added to the solids (previ-
ously dried) using a molar ratio CA:EG of 1:4. Solu-
tion was heated in a hot plate at constant agitation to
evaporate the excess of water. A dark green transpar-
ent gel was obtained after concentrating the solution
by slow evaporation. This gel was then dried in air
at 140 ºC for 24 h, Fnely ground in an agate mortar,
and burnt at temperatures from 400, 600 and 800 ºC
in air for 15 min in a tube furnace.
Figure 1
shows
a schematic experimental setup, indicating where
citric acid and ethylene glycol (CA-EG) is added.
NANO Cu/CuO FROM CYANIDATION WASTEWATER
267
The heat-treated samples were characterized by X-ray
diffraction (XRD) in a Siemens D-5000 diffractom-
eter operated at 25 mA and 35 kV. Experiments were
carried out in the 2θ range of 20 to 55 º at a step size of
0.02 degrees. Characterization by scanning electron
microscopy (SEM) with energy dispersive scanning
(EDS) was done in a Hitachi S-5500 microscope
operated from 10.2 to 10.5 A and 20 KV.
RESULTS AND DISCUSSION
Figure 2
shows the results of X-ray diffraction
obtained in samples ozonized during 6, 11 and 25 min
and Fnally heat treated in air at 400 ºC for 15 min.
Characteristic peaks of ZnO are observed for all of the
oxidation times in the cyanide solution investigated.
The presence of metallic Cu is observed in samples
obtained at ozonation time values of 11 and 25 min.
These results suggest that the ozonation time in cya-
nide solutions has a signiFcant effect on the resulting
species-type causing variations in the peaks intensi-
ties of the species present in samples synthesized by
sol-gel. Nevertheless, the Fnal species depended on
the heat treatment conditions.
The reactions occurring during treatment are
explained below. The ozonation of cyanide solution
occurs according to the following reaction. Gibb´s
free energy at 20 ºC was calculated from Outokumpu,
HSC Chemistry® for Windows 2002 software (Roine
2002):
Oxidation of free cyanide, CN
-
:
CN
+ O
3
= CNO
+ O
2
D
Gº = –443.2 KJ
(1)
Oxidation of metal cyanide complex:
Zn(CN)
4
2–
+ 4/3O
3
(g) = Zn
2+
+
4CNO
D
Gº = -1121.5 KJ
(2)
Cu(CN)
4
3-
+ 4/3O
3
(g) = Cu
+
+
4CNO
-
D
Gº = -1125.6 KJ
(3)
Precipitation
. Due to high pH solution (pH > 10),
the metal ions could precipitate as hydroxide once
the oxidation time for all free cyanide and cyanide
complexes is reached. However, metal ions can
precipitate as oxides due to continuous addition of
ozone, according to the following equations:
Zn
2+
+ 2/3O
3
(g) + 2OH
=
ZnO + H
2
O + O
2
(g)
D
Gº = –202.4 KJ
(4)
2Cu
+
+ 1/3O
3
(g) + 2OH
=
2CuO + H
2
O
D
Gº = –332.7 KJ
(5)
In the case of copper (major presence), the oxides
precipitation can be conFrmed by the precipitates
colorations: during ozonation a Frst blue precipitate
appears. Later the precipitate turns to brown and
Fnally to dark color. These colors emerge according
to copper transformations: of copper (I) hydroxide
Ozonation
column
o
o
o
o
o
o
o
o
O
2
O
3
o
o
o
o
o
Ozone generator
CA-EG
o o o
o o o
Dried
mufle
Tube furnace
Aqueous solution from
gold mining effluent
Fig. 1.
Schematic experimental setup. Citric acid (CA) and
ethylene glycol (EG)
6 min
11 min
Intensity (a. u.)
25 min
20
25
30
35
40
45
50
55
Cu
CuO
ZnO
2° (theta)
Fig. 2.
X-ray diffraction patterns from samples oxidized in dif-
ferent ozonation times, synthesized by sol-gel and a heat
treatment of 400 ºC under air atmosphere
M.J. Soria Aguilar
et al.
268
(blue) to copper (I) oxide (brown) and, fnally, copper
(II) oxide (dark) due to continuous ozonation.
In the sample with the shortest ozone injection
time (6 min), the presence of copper is not detected
by XRD because the oxidation of cyanide solution
starts with the decomposition of the most weak metal
cyanide complex, in this case Zn(CN)
4
2–
(stability
constant, log K
25ºC
= 19.6; Smith and Martel 1976,
Gerhardts 1987). Apparently, in the frst six minutes
of the ozone oxidation treatment, the time is not
suFfcient to obtain a signifcant amount oF the cop
-
per cyanide complex by decomposition. Only zinc
is precipitated and quickly oxidized by ozone. On
the other hand, the intensity of peaks for metallic
Cu is higher in samples with longer oxidation times
(11 and 25 min). The latter is due to the decomposi-
tion of a higher amount of copper cyanide complex,
Cu(CN)
4
3–
(log K
25ºC
= 23.1; Smith and Martel 1976,
Gerhardts 1987) and copper oxide precipitation, ac-
cording to equations 3 and 5.
Afterwards these precipitates are dissolved, re-
duced or complexed to form poly-chelates between
the C=O ligands of citric acid (CA) and metal ions.
In the Pechini method (Bennici
et al.
2003), the
chelate undergoes polyesterifcation while heating
with a polyfunctional alcohol like ethylene glycol
(EG). In the modifed Pechini method (combination
of the traditional Pechini and the citrate method) the
chelating process takes place during the evaporation
of the precursor solution containing metallic salts and
CA-EG. Furthermore, air heating produces a dark
viscous resin and a rigid transparent vitreous gel.
The presence of Cu in metallic state observed in
fgure 2
at 11 and 25 min during the heat treatment
at 400 ºC indicatees that heat treatment temperature
is insuFfcient to complete the combustion oF organic
matter (from citric acid and ethylene glycol). Then,
the reducing atmosphere generated during the heat
treatment at 400 ºC is suFfcient to the reduction
of copper oxide at copper zero-valent, according
to equation 6. However, these conditions are not
thermodynamically suFfcient to reduce the ZnO, as
indicated in equation 7:
CuO + C = Cu + CO(g)
D
400ºC
= –76.8 KJ
(6)
ZnO + C = Zn + CO(g)
D
400ºC
= +111.85 KJ
(7)
The average particle size calculated from the
data of XRD (sample treated with 25 min ozonation
and heat treatment at 400 ºC and 15 min) using the
Scherrer equation variess from 20 to 90 nm. Scherrer
equation is represented by the following equation
(Monshi
et al.
2012):
D
= Kl/b
Cos
q
(8)
In Scherrer’s formula, D = mean particle diameter,
K is the shape factor (K = 0.9),
l
is the x-ray wave-
length
(l
= 0.15417 nm), β is the line broadening
(full width) at half the maximum intensity (FWHM)
in X-ray spectrum (radians), and
q
is the Bragg angle.
Figure 3
shows a SEM photomicrography of
sample treated with 25 min ozonation and heat treat-
ment of 400 ºC for 15 min, where spherical particles
have a size between 50 and 130 nm. The EDS analysis
obtained in in a specifc particle (
Table I
) and the
respective qualitative elemental mapping confrm that
particles consist mainly of a mixture of particles of
Cu metallic and Cu oxides. Cu particles are deposited
in organic material (from CA-EG partially burned).
This result is in accordance with the initial chemical
analysis and with the XRD results: the synthesized
nanoparticles obtained at 400 ºC heat treatment are
predominantly Cu metallic.
When the heat treatment is performed at 800 ºC all
organic matter is consumed and the oxygen presence
(air atmosphere in chamber Furnace) is suFfcient to
oxidize the copper (
Fig. 4
). Furthermore, the intensity
of peaks corresponding to CuO increases, while those
of metallic Cu phase disappear.
Then, ozonation time is important to obtain suf-
fcient metal values and to destroy the dangerous
cyanide, making safe the subsequent sol-gel process.
Obviously, the gold mining eF±uent sample used in
this work is rich in copper, while the other metals (Zn,
Fe) are present in very low amounts. However, the
knowledge of the chemical reactions of complexes
oxidation, stability constants and oxidation-reduction
reactions during air dried and heat treatment permits
to set up adequate operation conditions to obtain
metal (or metal oxides), micro or nanoparticles
selectively.
CONCLUSIONS
According to the experimental results, an oxida-
tion treatment with ozone at alkaline pH allows the
oxidation of cyanide in the cyanide solution used in
this work. The pH > 10, cyanide and Cu amounts in
the industrial gold mining eF±uent indicate that Cu
is present in cyanide complexes Cu (CN)
4
3–
. Zinc is
also in solution as Zn (CN)
4
2–
.
During the oxidation
with ozone, both cyanide complexes are oxidized to
NANO Cu/CuO FROM CYANIDATION WASTEWATER
269
CuO and ZnO, respectively. Iron, another element in
the efFuent, forms a strong cyanide complex that is
not easily destroyed by ozone. Precipitates obtained
from oxidized solutions are subsequently complexed
with citric acid and ethylene glycol to obtain a sol-gel,
which is thermally treated.
±rom efFuent chemical analysis, the amount of
Cu is about 100 times higher than zinc. This implies
a greater number of XRD peaks associated with Cu
or CuO. The presence of metallic Cu in samples
thermally treated in air at 400 ºC is justi²ed by the
incomplete combustion of polymeric material that
generates a reducing atmosphere. When the heat
treatment is performed at 800 ºC, all polymeric
material is consumed and the presence of oxygen
(air atmosphere in chamber furnace) is enough to
oxidize the Cu. Furthermore, the intensity of peaks
corresponding to CuO increases, while those of metal-
lic Cu phase disappear as the temperature is increased
at 800 ºC. Although the diffraction results indicate the
presence of ZnO, its quantity is smaller than 1 % w/w.
TABLE I.
ENERGY DISPERSIVE SCANNING ANALYSIS
(CORRESPONDING TO
FIG. 3
) FOR SAM-
PLE TREATED WITH 25 MIN OZONATION,
SYNTHESIZED BY SOL-GEL AND HEAT
TREATMENT AT 400 ºC FOR 15 MIN
Element
C norm (wt. %)
Error (wt. %)
Cu
75.04
0.9
O
24.96
1.7
Total
100
UTSA 30.0kV 0.0mm x22.0k SE
2.00um
0.1259 μm
O-KA
Cu-KA
0.09020 μm
Fig. 3.
Scanning electron microscopy photomicrograph and mapping of sample treated with 25 min ozonation,
synthesized by sol-gel and heat treatment at 400 ºC for 15 min. Area with white lines in the micrograph
corresponds to the energy dispersive scanning analysis from
Table I
. Cu-KA = Cu-Kalpha, O-KA =
OK alpha (principal energy level, KeV)
Fig. 4.
X-ray diffraction patterns from samples oxidized in dif-
ferent ozonation times, synthesized by sol-gel and a heat
treatment of 800 ºC under air atmosphere
11 min
25 min
20
25
30
35
40
45
50
55
Cu
Cu O
Zn O
2° (theta)
Intensity (a. u.)
M.J. Soria Aguilar
et al.
270
SEM results confrm the presence oF Cu as metal or in
oxidized state, although a major control is necessary
to obtain small size nanoparticles. As conclusion, at
400 ºC and 800 ºC, relative good pure Cu metallic and
CuO nanoparticles, respectively, could be obtained
From ozonated Cu-rich gold mining eF±uents by the
Pechini modifed sol-gel method.
This preliminary work shows the possibility of us-
ing industrial wastewater as low-cost raw material to
obtain high-value compounds, as metallic and oxide
metal nanoparticles. In this case, the combination
of the two methods, (ozonation and sol-gel synthe-
sis), represents a low-cost alternative for obtaining
nanoparticles From industrial gold mining eF±uents.
ACKNOWLEDGMENTS
The authors would like to thank the International
Center for Nanotechnology and Advanced Materi-
als - Kleberg Advanced Microscopy Center - at the
University of Texas, San Antonio (ICNAM-UTSA)
for their technical assistance with the SEM charac-
terization.
REFERENCES
Bennici S., Gervasini A. and Ragaini V. (2003). Prepara-
tion of highly dispersed CuO catalysts on oxide sup-
ports for de-NOx reactions. Ultrasonics Sonochem.
10, 61-64.
Gadhe J. and Gupta B. (2007). Hydrogen production by
methanol reforming in supercritical water: Catalysis
by in-situ-generated copper nanoparticles. Int. J. Hy-
drogen. Energ. 32, 13, 2374-2381.
Gerhardts W. (1987). Ullman’s encyclopedia of industrial
chemistry, 5th edition, VCH, Weinheim, Germany,
639 pp.
Gvishi R. (2009). Fast sol–gel technology: from fabri-
cation to applications. J. Sol-Gel Sci. Technol. 50,
241-253.
Habashi F. (1966). The theory of cyanidation. Transactions
of the mineralogical society of AIME. 235, 236-239.
Huang Z., Cui F., Kang H., Chen J. and Xia C. (2009).
Characterization and catalytic properties of the CuO/
SiO2 catalysts prepared by precipitation-gel method
in the hydrogenolysis of glycerol to 1,2-propanediol:
Effect of residual sodium. App. Catal A. 366, 288-298.
Kakihana M. (1996). Sol-gel preparation of high tempera-
ture superconducting oxides. J. Sol-Gel Sci. Technol.
6, 7-55.
Lanje A., Sharma S., Pode R. and Ningthoujam R. (2010).
Synthesis and optical characterization of copper oxide
nanoparticles. Adv. Appl. Sci. Res. 1, 2, 36-40.
Ministry of Environment Ontario (2013). Safe drinking
water act, 2002 and amendment in 2006 [online].
Monshi A, ²oroughi M. and Monshi M. (2012). Modifed
scherrer equation to estimate more accurately nano-
crystallite size using XRD. World J. of Nano Sci. and
Eng. 2, 154-160.
Mudliara R., Umareb S.S., Ramtekea D.S. and Wate S.R.
(2009). Energy eFfcient—Advanced oxidation pro
-
cess for treatment of cyanide containing automobile
industry wastewater. J. Hazard. Mater. 164, 1474-1479.
Potemkina D., Snytnikova P., Pakharukova V., Semina G.,
Moroza E. and Sobyanina V. (2010). Copper–cerium
oxide catalysts prepared by the Pechini method for CO
removal from hydrogen containing mixtures. Kinet.
Catal. 51, 1, 119-125.
Rahaman M. (2007). Ceramic processing, CRC Press.
Boca Raton, Florida, USA, 388 pp.
Ren G., Hu D., Cheng E., Vargas-Reus M., Reip P. and
Allaker R. (2009). Characterization of copper oxide
nanoparticles for antimicrobial applications. Int. J.
Antimicrob. Agents. 33, 6, 587-590.
Roine A. (2002). Outokumpu, HSC chemistry® for
windows (2002). Chemical reaction and equilibrium
software with extensive thermochemical database.
Outokumpu Research Oy. Finland.
Rubo A., Kellens, R., Reddy J., Steier N. and Hasenpusch
W. (2006). Alkali metal cyanides, in Ullmann’s ency-
clopedia of industrial chemistry, Wiley-VCH, Wein-
heim, Germany [online]. http://onlinelibrary.wiley.
com/doi/10.1002/14356007.i01_i01/abstract
Segal D. (1997). Chemical synthesis of ceramic materials.
J. Mater. Chem. 7, 1297-1305.
Smith R. M. and Martel A. E. (1976). Critical stability
constants, volume 4: Inorganic complexes. Plenum
Press, New York, USA, 469 pp.
Theivasanthi T. and Alagar M. (2011). Nano sized copper
particles by electrolytic synthesis and characteriza-
tions. Int. J. Phys. Sci. 6, 3662-3671.
logo_pie_uaemex.mx